padook

joined 2 years ago
[–] padook@feddit.nl 10 points 2 months ago

I'm really going to miss Self-Hosted, it brought a community of us weirdos together. I hope someone fills the vacuum left after ep. 150

[–] padook@feddit.nl 3 points 3 months ago (1 children)

I have two TV boxes, one is a Raspberry pi 4, the other is a pi 5. I installed KonstaKANG's android port for the Pi's. Depending on your familiarity with flashing the Pi's this video from Explaining Computers offers a way to get Konsta installed through PINN. Once they're up and running they act just like a cellphone. This remote works really well.

Install f-droid, and/or obtainium, and/or Aurora Store and you can install whatever apps you want on the box.

I don't personally use Chromecast, so I can't vouch for that working. Mine is more centered around consuming Jellyfin (jellyfin android tv app), youtube (newpipe), podverse, and Radiodroid

I really liked Kodi, but could never get it to correctly sync across devices so I finally went the android route. I've been pretty happy

Feel free to pick my brain if you have more questions

[–] padook@feddit.nl 3 points 3 months ago (3 children)

I dont think I so much want this for my phone as for my homemade AndroidTV boxes. Losing the Linux functionality after switching from Kodi/libreelec had been my biggest pain point.

Can't wait to see my TV boxes show up in my Beszel dashboard!

[–] padook@feddit.nl 18 points 4 months ago

Fuuuuuckkkk I wish I could degoogle again

Don't be evil, lol

[–] padook@feddit.nl 3 points 7 months ago

Thank you for this

[–] padook@feddit.nl 2 points 1 year ago

I agree about the USB Ethernet dongle. Unless you only require short distance wifi range (eg hotel room temp router) the radio in the pi isn't going to be enough

I built a pi4 router a few years ago, and it's still running great, I recommend the project. But unfortunately I can't find the HOWTO and it was before I started taking good notes. I assume your current router is a phone company supplied modem/router?

My setup is cable modem-->pi router-->switch--> old netgear router in Access point only mode

Being that your router/modem is upstream of router, I'm not sure if you could pass-through the WAN to the pi router, and pass back the LAN to the router/modem for the wifi... maybe someone on here can shed some light?

[–] padook@feddit.nl 11 points 1 year ago

I could have the best self hosted setup.... living in a van, down by the river!

[–] padook@feddit.nl 1 points 1 year ago

This thought came to me this morning. I have 4 machines both because the BEAST grows organically, and because we're always trying to avoid that single point of failure. Then a scenario comes along that makes you question your whole way of thinking, diversifying may actually create more problems

[–] padook@feddit.nl 16 points 1 year ago (6 children)

I didn't mean to imply that Services actually broke. Only that they didn't come back after a reboot. A clean reboot may have caused some of the same issues because, I'm learning as I go. Some services are restarted by systemctl, some by cron, some....manual. This is certainly a wake up call that I need standardize and simplify the way the services are started.

 

I woke up this morning to a text from my ISP, "There is an outage in your area, we are working to resolve the issue"

I laugh, this is what I live for! Almost all of my services are self hosted, I'm barely going to notice the difference!

Wrong.

When the internet went out, the power also went out for a few seconds. Four small computers host all of my services. Of those, one shutdown, and three rebooted. Of the three that ugly rebooted some services came back online, some didn't.

30 minutes later, ISP sends out the text that service is back online.

2 hours later I'm still finding down services on my network.

Moral of the story: A UPS has moved to the top of the shopping list! Any suggestions??

[–] padook@feddit.nl 1 points 1 year ago (1 children)

Your problem may differ from mine, but whenever I've been greeted with the command line in grub the solution has actually been in bios. I'll leave you with my notes, which are a bit snarky after spending a lot of time trying to figure out hot to repair grub, when the solution was 3 clicks in bios:

"Inspiron won't boot

Goes to the grub command prompt

Don't fuck with that thing

Restart, F2 to get into bios

Change boot sequence to start the SSD first, not ubuntu

Reboot, itll do it a couple times, but should boot right into normal grub"

I hope your solution is the same

[–] padook@feddit.nl 3 points 1 year ago

Slaps forehead I know I read that guide too....whether I forgot about it or thought that would do something else... Thank You!

 

I've been slowly moving access to my Self hosted services from multiple WireGuard VPN connections over to tailscale for that nice flat network feel. One thing that was holding me back from the switch was that I liked vpn'ing my internet traffic from my phone and laptop back to my network and into the PiHole to avoid ads/tracking when I was away from home.

Then I found the DNS settings on the tailscale admin console and everything lit up! I added the server that PiHole is running on as a nameserver and changed the global settings and BINGO! No ads!

Unfortunately.... A few days later when looking at my PiHole admin console I realized that the PiHole that I set up at my parents house for them was one of the biggest clients.....Not optimal.....

Is there a way to make an exception to the global DNS setting? Any suggestions? I don't want to remove their PiHole from my tailnet as it makes it much easier to maintain.

[–] padook@feddit.nl 31 points 1 year ago (3 children)

I'm sorry, what?....Oh, all I heard was that my linux home server is going to be running on new hardware in about a year and a half when all these used computers go on sale. 😁

view more: next ›